TestIT:Configuration Serial Advanced - Revision history

NolekAdmin at 13:57, 11 September 2019

2019-09-11T13:57:08Z

NolekAdmin: /* 6.3.12.1 Commands */

2019-09-10T12:50:30Z

6.3.12.1 Commands

NolekAdmin at 12:50, 10 September 2019

2019-09-10T12:50:08Z

NolekAdmin at 12:49, 10 September 2019

2019-09-10T12:49:40Z

NolekAdmin: Created page with "===6.3.12 Serial advanced=== In serial advanced there is a communication with a serial port with advanced features. '''Setup fields:''' # Configuration # Send/receive parame..."

2019-08-23T08:41:55Z

Created page with "===6.3.12 Serial advanced=== In serial advanced there is a communication with a serial port with advanced features. '''Setup fields:''' # Configuration # Send/receive parame..."

New page

===6.3.12 Serial advanced===

In serial advanced there is a communication with a serial port with advanced features.

'''Setup fields:'''
# Configuration
# Send/receive parameters
# Test device

'''''Configuration:'''''
# Write the device name and device description (required)
# Select if the device is active or not
# Select the following:
## Baud rates – Serial port parameter
## Data bit - Serial port parameter
## Parity - Serial port parameter
## Stop bit - Serial port parameter
## Com port – Will show all registered COM ports on the PC
## Send termination char – Where the char must send the communication
## Receive termination char - Where the char should receive the communication
## Send as – Text or byte array
## Send encoding – None or Char to Hex
## Send params – Number of sending parameters
## Receive delimiter – Which character to split the received text
## Receive params – Number of receiving parameters
## Receive as – Text or byte array
## Receive encoding – None or char to Hex
# Press Save

'''''Send/receive parameters:'''''
* Send parameters – Symbol values to be sent to the COM port.
* Receive parameters – Connect the received data from COM port together with symbols. Values will be separated by receive delimiter.

'''''Test device:'''''
There are two types of tests; a standard test and one where the use the command parameters is included. After the wanted tests, it is possible to clear the text, at the clear received text button. When the tests are finished, press Unlock config and Save.

''To run a standard test:''
# Press the test device tab
# Press Lock config to open the COM port
# Insert text in the command field to send.
## If byte array is selected in send as, use a space separated structure to fill the byte array. - E.g. “15 53 24 11 01”.
## If Char to Hex is selected in send encoding, the values will be encoded.
# Press Send and the received text will be shown in the read box.

To run a test including the use of command parameters:
# Press the test device tab
# Press Lock config to open the COM port
# Insert text in the command field to send.
## If byte array is selected in send as, use a space separated structure to fill the byte array. - E.g. “15 53 24 11 01”.
## If Char to Hex is selected in send encoding, the values will be encoded.
# Select “use command parameters”.
# Write the type in the criteria.
## If the result should be received, then write the same as in the command.
# Select the criteria type as in the command.
## None; Begins with; Contains.
# Press Send and the received text will be in evaluation.
# The command response will be the same response as the result of the command. This is based on the evaluation above.

====6.3.12.1 Commands====

Command in serial advanced is:
* [[TestIT:Programming_S9RS232|RS232ADV]]

← Older revision		Revision as of 13:57, 11 September 2019
Line 64:		Line 64:

	Find a code example and the parameters in the functions window, in section serial.		Find a code example and the parameters in the functions window, in section serial.
		+
		+
		+	[[TestIT:Configuration#Devices_in_TestIT%3A\|Back to Configuration]]

← Older revision		Revision as of 12:50, 10 September 2019
Line 62:		Line 62:
	Command in serial advanced is:		Command in serial advanced is:
	* [[TestIT:Programming_S9RS232\|RS232ADV]]		* [[TestIT:Programming_S9RS232\|RS232ADV]]
		+
		+	Find a code example and the parameters in the functions window, in section serial.

@@ Line 44: / Line 44: @@
 # Press Send and the received text will be shown in the read box.
-To run a test including the use of command parameters:
+''To run a test including the use of command parameters:''
 # Press the test device tab
 # Press Lock config to open the COM port

← Older revision		Revision as of 12:49, 10 September 2019
Line 33:		Line 33:

	'''''Test device:'''''		'''''Test device:'''''
		+
	There are two types of tests; a standard test and one where the use the command parameters is included. After the wanted tests, it is possible to clear the text, at the clear received text button. When the tests are finished, press Unlock config and Save.		There are two types of tests; a standard test and one where the use the command parameters is included. After the wanted tests, it is possible to clear the text, at the clear received text button. When the tests are finished, press Unlock config and Save.