TestIT:Configuration S9 Serial - Revision history

NolekAdmin at 13:56, 11 September 2019

2019-09-11T13:56:26Z

NolekAdmin at 07:08, 10 September 2019

2019-09-10T07:08:26Z

MartinHeide at 13:50, 9 September 2019

2019-09-09T13:50:14Z

NolekAdmin: Created page with "===6.3.10 S9 Serial=== S9 Serial device is the communication to Nolek S9. Recipes can be created from TestIT and send directly to the S9. '''Setup fields:''' * Configuration..."

2019-08-23T08:35:53Z

Created page with "===6.3.10 S9 Serial=== S9 Serial device is the communication to Nolek S9. Recipes can be created from TestIT and send directly to the S9. '''Setup fields:''' * Configuration..."

New page

===6.3.10 S9 Serial===

S9 Serial device is the communication to Nolek S9. Recipes can be created from TestIT and send directly to the S9.

'''Setup fields:'''
* Configuration
* Symbols
* Recipes
* Test device

'''''Configuration:'''''
# Write the device name and device description (required)
# Select if the device is active or not
# Select the following:
## Baud rates – Serial port parameter
## Data bit - Serial port parameter
## Parity - Serial port parameter
## Stop bit - Serial port parameter
## Com port – Will show all registered COM ports on the PC
## Recipe Handling – Where to get recipes from; TestIT or Moscura
## Log measure – Select only to store measurement values
## Log folder path – Path of folder to store log in
## Graph Y axis min – Set a minimum for the Y axis. Auto if 0.
## Graph Y axis max – Set a minimum for the Y axis. Auto if 0.
## Graph secondary Y axis min – Set a minimum for the secondary Y axis. Auto if 0.
## Graph secondary Y axis max – Set a minimum for the secondary Y axis. Auto if 0.
# Press Save

'''''Symbols:'''''
# Press the symbols tab
# Select the symbols for the spaces

'''''Recipes:'''''
# Select Open the test are symbol and the recipes will be shown
# Add a new recipe
## Press New
## Write the recipe name (required)
## The optional spaces: Info, Recipe, Auto Control, Shock Fill, Vacuum pressure, Dosage, Volume Control, Flow, Offset Compensation, Quick Connector, Setting.
# Copy the recipe
## Press Copy
## Write a new recipe name
## Press Save
# Delete the recipe
## Choose the wanted recipe
## Press Delete and accept

'''''Test device:'''''
# Select the test symbol and it will open a new tab
# To start the test, Press Connect
# To stop the test, Press Disconnect

====6.3.10.1 Commands====

Commands in S9 serial are:
* [[TestIT:Programming_S9RS232#Measure|Measure]]
* [[TestIT:Programming_S9RS232#StartInstrument|StartInstrument]]
* [[TestIT:Programming_S9RS232#ControlLeak|ControlLeak]]
* [[TestIT:Programming_S9RS232#RecipeNumber|RecipeNumber]]
* [[TestIT:Programming_S9RS232#RecipeText|RecipeText]]
* [[TestIT:Programming_S9RS232#MeasureLog|MeasureLog]]
* [[TestIT:Programming_S9RS232#RecipeValuesAsText|RecipeValuesAsText]]

@@ Line 60: / Line 60: @@
 * [[TestIT:Programming_S9RS232#MeasureLog|MeasureLog]]
 * [[TestIT:Programming_S9RS232#RecipeValuesAsText|RecipeValuesAsText]]
 ==How to==
 <embedvideo service="youtube">https://youtu.be/zgxJx_hNrh4</embedvideo>

← Older revision		Revision as of 13:50, 9 September 2019
Line 60:		Line 60:
	* [[TestIT:Programming_S9RS232#MeasureLog\|MeasureLog]]		* [[TestIT:Programming_S9RS232#MeasureLog\|MeasureLog]]
	* [[TestIT:Programming_S9RS232#RecipeValuesAsText\|RecipeValuesAsText]]		* [[TestIT:Programming_S9RS232#RecipeValuesAsText\|RecipeValuesAsText]]
		+
		+	==How to==
		+	<embedvideo service="youtube">https://youtu.be/zgxJx_hNrh4</embedvideo>

@@ Line 18: / Line 18: @@
 ## Stop bit - Serial port parameter
 ## Com port – Will show all registered COM ports on the PC
-## Recipe Handling – Where to get recipes from; TestIT or Moscura
+## Recipe Handling – Where to get recipes from; TestIT or mosCura
 ## Log measure – Select only to store measurement values
 ## Log folder path – Path of folder to store log in
@@ Line 32: / Line 32: @@
 '''''Recipes:'''''
-# Select Open the test are symbol and the recipes will be shown
+# Select Open the test area/View recipes button and the recipes will be shown
 # Add a new recipe
 ## Press New
 ## Write the recipe name (required)
-## The optional spaces: Info, Recipe, Auto Control, Shock Fill, Vacuum pressure, Dosage, Volume Control, Flow, Offset Compensation, Quick Connector, Setting.
+## The optional spaces: Info, Recipe, Auto Control, Shock Fill, Vacuum pressure, Dosage, Volume Control, Flow, Offset Compensation, Quick Connector, Setting, Type, Fill, Stab, Measure, Vent, Misc.
 # Copy the recipe
 ## Press Copy
@@ Line 46: / Line 46: @@
 '''''Test device:'''''
-# Select the test symbol and it will open a new tab
+# Select the test button and it will open a new tab
 # To start the test, Press Connect
 # To stop the test, Press Disconnect